02-05-10, 03:39 AM | #1 |
BassFishin.Com Member
Join Date: Feb 2010
Location: Rochester, MN
Posts: 34
|
First brand new baitcaster...
So I just bought a brand new Curado 201E7 off ebay for $130, which I thought was a great price and I'm excited to receive. My question is...is there anything I should do to prep it before I use it the first time? Or just spool it up and go fishing?
|
02-05-10, 08:38 AM | #2 |
BassFishin.Com Super Veteran
|
First of all, excellent pick. Just check it out of the box. I am not much of a reel guru, so I just spool mine up and go to slinging after a look over out of the box.
__________________
\,,,,/ ROCK ON! HRN4L! |
02-05-10, 09:23 AM | #3 |
BassFishin.Com Veteran Member
Join Date: Jan 2010
Location: albemarle, NC
Posts: 788
|
Same for me.
__________________
138 bass in 2K10. Biggest 4LBS 14oz. |
02-05-10, 09:43 AM | #4 |
BassFishin.Com Premier Elite
|
Here's something I wrote a while ago to help baitcasting newbies.
New to Baitcasters: Properly Adjusting Your Reel One of the biggest problems people have when learning how to fish with a baitcasting reel is getting all the settings right. If you don't set the reel correctly, you'll most likely get frustrated by a lot of backlashes. But if you follow these steps, you'll be casting successfully in no time. Before we go over the steps to properly adjusting a baitcaster, I want to talk about fishing line for a bit. When learning to use a baitcaster, no matter how well it is adjusted, you're going to get some backlashes. Because of this, I never recommend using a fluorocarbon (FC) line when learning to fish with a baitcaster. If you’re wondering why, tt's because most FC lines will be damaged when a bad backlash occurs. You may not even know it and on the next cast, you're lure goes flying. I have had this happen to be with a brand new spool of FC line and trust me, it sucks. While braid will not be damaged by most backlashes, if a serious one occurs, it may need to be cut out and replaced. With braid, this can become costly quite fast. So, when learning on to fish a baitcaster, use mono. It can stand the abuse of backlashes without serious damage, and if you need to cut it out and replace it, it's relatively inexpensive. The first step in properly adjusting a baitcaster is setting the spool tension. The spool tension knob is located on the same side of the reel as the handle, normally right behind the star drag. To set this, reel your bait almost to the tip of your rod (within a couple inches). Hold your rod up at a 45 degree angle to the ground. Push the thumb bar and let the reel free spool. Make sure you stop the bait before it hits the ground. If the bait falls quickly, tighten the knob slightly. Repeat this process until the bait falls very slowly or won’t start falling unless you give the rod a little shake. A good rule of thumb if the bait should take around 5-6 seconds to reach the ground. When tightening the spool tension knob, a little turn goes a long way. You’ll need to do this almost every time you switch lures, especially when the weight changes a lot. Next up are the brakes. There are three different types of brakes, and I’ll cover all three and how to set them. First are Magnetic Brakes. Magnetic brakes work just like the name implies. Magnets are used to keep the spool’s speed in check. Daiwa makes use of magnetic brakes in their reels, as do some Abu Garcia’s. All magnetic braking reels have a dial of some sort on the opposite side of the reel as the handle. These dials can be numbered, from 0-10 or labeled “MIN” to “MAX”. Either way, it’s the same concept. For beginners to, I suggest starting with your magnetic brake turn on to about 70%. So number 7 on a 0-10 or OFF-10 dial. When you get good at casting like this and you feel confident enough, you can back it down to about 60%. When learning I went down 5-10% each time I felt comfortable enough. I am currently casting at about 25-40% Next are Centrifugal Brakes. These brakes make use of “pins” attached to the spool that apply pressure as the spool spins faster to slow it down. Shimano, some Abu Garcia reels, and others make use of centrifugal brakes. The adjustment of most centrifugal brakes requires you to take the side plate off your reel. Abu Garcia reels require you to unscrew a little screw and twist the side plate while some of the newer Shimano’s have a little handle like device that you turn to open the side plate. Refer to your owner’s manual for directions on removing the side plate. Once inside, you’ll notice the 6 “pins” I referred to earlier. All reels pins are built different, but again, it’s the same concept. It’s important to remember that these pins must be set SYMETRICALLY, if they are not, they will not work correctly. This means you have fewer options with these brakes than you do with magnetic brakes. You can have no pins on, 2 on, 4on, or all 6 on. So, if you turn one pin on, the one across from it must be turned on. You can also turn on three by alternating every other one. To turn each pin on, push it out. To turn it off, push it in until it clicks. I remember this by a simple trick. “I fish often” The word OFTEN sounds like the words OFF and IN, therefore, you’ll remember the brakes are OFF when they’re pushed IN. To start, I’d use all six or four of them. Right now, I use 2 or 3 depending on the reel I’m fishing with. Finally, you have Dual Brakes. Again, exactly what it sounds like. This is a combination of Magnetic and Centrifugal brakes. Bass Pro Shops reels, Pflueger, and some of the newer Abu Garcia reels use this technology. Setting these brakes is exactly the same as stated above, except, when used in combination, you don’t have to set them as high. To start, I’d set the magnetic brake to 50% and the centrifugal to 3-4 pins on. Currently, I have the magnetic brake on 10-20% and 2 pins on with the centrifugal brake. One thing I can’t stress enough about the brakes as a beginner, and even when you get really good, is turn the brake up slightly when fishing in strong wind. I learned this lesson the hard way with some serious backlashes. I hope these tips help you become better at fishing with a baitcaster, but remember, the best thing you can do to get better is spend time on the water! BB
__________________
As of June 14, 2014 the members of the BF.com forum have moved to basschat.yuku.com! |
02-05-10, 05:25 PM | #5 |
BassFishin.Com Super Veteran
Join Date: Nov 2004
Location: Pitts. Pa.
Posts: 3,801
|
A lot of guys clean and re-oil and grease them. I don't. A lot of guys like certain brands of lubes. Just watch out because if you use the Hot Sauce stuff it might void your warrenty if it isn't a Quantum product.
__________________
you can have my fishin rod when ya take it from my cold dead hands |
02-05-10, 05:35 PM | #6 |
BassFishin.Com Premier Elite
Join Date: Mar 2009
Location: Southwest IN
Posts: 5,630
|
I'm confused...it this your first time using a baitcaster? Or just your first brand new baitcaster?
__________________
Many men go fishing all of their lives without knowing it is not fish they are after. |
02-05-10, 05:40 PM | #7 |
BassFishin.Com Member
Join Date: Feb 2010
Location: Rochester, MN
Posts: 34
|
Yeah, sorry I wasn't clear. I've got a couple other baitcasters, an older bantam curado and a pflueger trion, however they were both used when I got them. This is my first BRAND NEW baitcaster.
Last edited by MN Bass Man; 02-05-10 at 05:49 PM. |
02-05-10, 07:08 PM | #8 | |
BassFishin.Com Premier Elite
|
Quote:
I normally don't do much to new reels before I fish them. Some guys clean the bearings and relube them right out of the box. Check out the "Changing out Bearings" thread for more info on this. BB
__________________
As of June 14, 2014 the members of the BF.com forum have moved to basschat.yuku.com! |
|
02-05-10, 08:45 PM | #9 |
BassFishin.Com Member
Join Date: Feb 2010
Location: Rochester, MN
Posts: 34
|
|
02-05-10, 08:58 PM | #10 |
BassFishin.Com Premier Elite
Join Date: Jun 2003
Location: San Antonio, TX
Posts: 10,141
|
Welcome to the forum!
Take a look here: http://pages.infinit.net/fishing/bait101.htm That will get you ready to go. THEN go fishin!
__________________
It's happened to the best of them: John 21:3 |
02-05-10, 09:29 PM | #11 |
BassFishin.Com Premier Elite
Join Date: Mar 2009
Location: Southwest IN
Posts: 5,630
|
I think when you get a new baitcaster, it's a good idea to use it a while before you start monkeying with it. If something in it is broken or defective, you might not know for sure you didn't do it with your hot-rodding or your favorite warranty-voiding lube.
__________________
Many men go fishing all of their lives without knowing it is not fish they are after. |
02-05-10, 10:13 PM | #12 |
BassFishin.Com Super Veteran
Join Date: Sep 2009
Location: Dallas, TX
Posts: 4,671
|
Great post BB.
I always take apart new reels and flush and re-lube the bearings, they are normally packed with grease. If you aren't comfortable doing this, don't, it isn't really absolutely necessary. |
Disclosure / Disclaimer
Before acting on the content posted, you should know that BassFishin.Com may benefit financially and otherwise from content, advertising, links or otherwise from anything you click on, read, or look at on our website. Click here to read our Disclosure Policy and Disclaimer. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|