09-10-06, 11:22 AM
|
#1 |
|
BassFishin.Com Super Veteran
Join Date: Sep 2002
Location: Lexington,NC-Worlds best BBQ.
Posts: 1,945
|
Keelguard
My Keelguard is coming loose. Is there as glue or some type of adhesive which will prevent this ?
__________________
Lexington,NC. |
|
|
|
09-10-06, 12:05 PM
|
#2 |
|
BassFishin.Com Premier Elite
Join Date: Jan 2004
Location: denton nc
Posts: 13,441
|
same stuff they use on it 3m marine adheasive.problem is if they don't get the bubbles out when they put it on. it will come loose like yours..
zooker
__________________
the godfather.. aml in remission since 7-20-09 |
|
|
|
|
09-10-06, 03:31 PM
|
#3 |
|
BassFishin.Com Super Veteran
Join Date: Aug 2004
Location: New Jersey
Posts: 2,638
|
Keelguards are for fiberglass boats right? Do they make them for aluminum or is it pointless?
__________________
fivealivebassmasters.com |
|
|
|
|
09-10-06, 04:14 PM
|
#4 |
|
BassFishin.Com Premier Elite
Join Date: Jan 2004
Location: denton nc
Posts: 13,441
|
yes they do power.
zooker
__________________
the godfather.. aml in remission since 7-20-09 |
|
|
|
|
09-10-06, 04:30 PM
|
#5 |
|
BassFishin.Com Premier Elite
Join Date: Mar 2005
Posts: 8,655
|
I'd say you must use a good cleaner for the boat before ya stick a guard on, theres a 3M adhesive on the backside of guard, easily found on the internet for the do-it-yerselfer...
|
|
|
|
|
09-10-06, 04:33 PM
|
#6 |
|
BassFishin.Com Super Veteran
Join Date: Aug 2004
Location: New Jersey
Posts: 2,638
|
Zook,
Any idea what they would run for a 16ft 3 in Bass Boat?
__________________
fivealivebassmasters.com |
|
|
|
|
09-10-06, 05:43 PM
|
#7 |
|
BassFishin.Com Premier Elite
Join Date: Jan 2004
Location: denton nc
Posts: 13,441
|
$110 or so bps has them make sure they are for aluminum i think they are 5" wide as glass ones are 7" wide..
zooker
__________________
the godfather.. aml in remission since 7-20-09 |
|
|
|
|
09-11-06, 02:58 PM
|
#8 |
|
BassFishin.Com Super Veteran
Join Date: Sep 2002
Location: Lexington,NC-Worlds best BBQ.
Posts: 1,945
|
JB,
Went by the instructions. Sand,apply cleaning solution and then apply main item. No problems getting the area clean. On the tape it showed the guy putting this Keelguard on a boat that was above his head. Give me a break, it was a new boat as well. Mine is on the trailer and when off the water thats where it'll stay. (I hope) Zook, thanks for the info. May have to remove the entire item and get a new one or fasten the old one back on with "new" glue.
__________________
Lexington,NC. |
|
|
|
|
10-14-06, 06:17 AM
|
#9 |
|
BassFishin.Com Super Veteran
Join Date: Aug 2005
Location: crossett,arkansas
Posts: 2,777
|
LOL!!! Good ole marine epoxy appled cprrectly will keep her in place. Clean it up and STICK HER LOL
__________________
Laser's rule with Merc's doing the pushing..........KEEP THE WETSIDE DOWN AND THE DRY SIDE UP!!!!!! |
|
|
|
 |
|
Disclosure / Disclaimer
Before acting on the content posted, you should know that BassFishin.Com may benefit financially and otherwise from content, advertising, links or otherwise from anything you click on, read, or look at on our website. Click here to read our Disclosure Policy and Disclaimer. |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
